Intruder Alarms

Hi, I had an alarm system and we started having problems with our bell box (kept going off because it was too close to the boiler flue). I decided to replace the bell box and bought a Texecom Odyssey 1E. We've fitted the bellbox but it won't seem to work with my existing system. I'm not sure but it may be that its not compatable with the panel/key pad. I could do with knowing what panel/keypad would work with this bell box, how much they cost and whether you stock such an item. Thanks

Hi can anyone help me, I have installed this alarm system myself and i can set it fully,however I cant part set it. I have gone through the programs ,program 1 does everything,program 2 i have set up to just do downstairs. I have gone through the manual and done as it says, but when i set the alarm it says that once the code is typed in and the countdown begins press 'P' and the tone will stop then press the program you wish ie. 2. But for me the countdown doesnt stop, I press 'P' and 2 and it does nothing and it still says program '1' on the LCD keypad. Please help before I use a hammer on it as it is very frustrating!!!!! Please help thanks

I have fitted the above on a upc window. 1. the led is continuously flashing. Is this correct? 2. The unit is fitted to the position A at right hand side of the frame and will alarm on tapping the right hand panel but not when tapping the left hand panel. Are two units required on the window frame?

i am after a scan 9943 with 5 or 6 remotes. Will the keypad pair up ok with a 9930. How much is a 9941 & 9943 & fobs

Can you tell me if there is any benefit to having an mcs-730 over a mcs-710 other than being 10db louder?

can you tell me dose the snt duolink kit come with psu

I have a omnicron 7000 and i wish to change the controll panal i was wondering if you had a panal that would be able to be put in its place and i could just rewire my sensers back in to

upon power uo of my recently purchased optima gen4 copact alarm the alarm sounds- enter code 0123 and the alarm siren silences. i have no flashing tamper light despite the cover being off,i have a flashing sos led which will not go out whatever i press? i have the global tamper pa & ta terminals shorted out but still am unable to extinguish the sos led. do you think the unit is faulty or am i missing something obvious

Does the Honeywell AG6 SAB and Cover (Blue Strobe)have led indicators on perm or flashing, to indicate power is there and it is not a dummy box.

I have a texecom premier which has alarmed but I cannot re set it as it looks like it may need an engineers code. Is there some way of re booting it to put it back to factory default codes. If not, rather than call out the alarm company is it possible to just replace the control panel. Do I need to replace the local lcd keypad as well. If I disconnect the control panel to replace it will the external siren go off? Regards

Hi, Can you advise on a simple and robust wired alarm for a cold and damp Scout hut. I will be installing it myself but I don't expect major problems with that side of things... We need: 5 PIRS 1 key pad 3 door detectors 2 external bells (preferably) 1 dummy box 1 internal sounder and about 200m of cable No need for distinct key codes or anything like that. Thanks

I think I need 11 zones: Kitchen door (E/E) Front Door (E/E) Workshop PIR Garage PIR Lounge (Pet Friendly PIR) Hallway 1 (Inhibited Pet Friendly PIR for E/E) Hallway 2 (Pet Friendly PIR) Bedroom 1 (Pet Friendly PIR) Bedroom 2 (Pet Friendly PIR) Dining room (Pet Friendly PIR) Kitchen (Inhibited Pet Friendly PIR for E/E) 1 x RKP External Sounder Is there a system/ kit that will do this (Honeywell Galant? - is this panel obsolete?) or can I link multiple PIR's to use the 8 zone kit as advertised Honeywell ADE LCD Accenta 4 x Pet PIR Starter Kit

SInce i live in Sweden i have a Swedish system. Its a Visonic with a builtin GSM. Not sure what that model i called in UK since the alarm doesn

I have purchase from Security Warehouse an ADE Honeywell Easy Set Unit with an ADE Honeywell Accenta Metal Gen 4. The instructions for the Easy Set provide Wiring Details for connection to a G3 and an Accenta 8 Panel, but there is no wiring and program changes for a Gen 4. How is the wiring configured and what program changes are necessary. Our Reference Secware 3 sent 19.45 on the 5th of November.

I need some help to choose an alarm system. My house is approximately 230 sqM and in all doors and windows I have mounted wired magnetic sensors with 4 wires, 2 for when the window/door is opened and 2 for sabotage safety so you can

i'd like to fit an alarm system into my double garage but am not sure which is the right kit to fit. I've installed a Texecom into my house which i'm very happy with so ideally would like to use their kit again if possible. I'd like to keep the house and garage system completely seperate. By my reckoning i need 1 x control pannel with keypad for in the garage 1 x remote keypad for in the house (incase of false alarm activation) 2 x suitable garage PIRs 1 x remote control (for controlling from the car as the doors are remote controlled also) 1 x red LED flashing external light to show alarm is set 1 x external strobe to show alarm has been activated 1 x internal…

I have just purchased the rs232 remote programmer but it is saying that I need to enter installer mode to access this. The main reason I bought the pack was because I could not get the installer option on the menu and I have forgotted the installer code. I have already tried a master reset but to no avail. Please could you advise if you are able to assist.

Please could you tell me the replacement for the Scantronic 4600r wireless burglar alarm system? I'm not sure if my control box is faulty (although there is a significant chance that this is the case) or if one of the window/door vipers is faulty, but my system is 13 years old, and I think it may need to be changed.

My system is showing a fault "Telecommand Batt Low" which refers to the 723r Telecmmand remote setting device. I have changed the batteries in the 3 telecommand devices I have however the system continues to show the error. I have moved the system into Engineer mode and it will not now exit. Going through the command set to exit Engineer Mode ie 99 tick, the systems goes through the "checking system bus" bit ok and after agreeing to "exit eng" the unit starts the "Checking System" routine and then flags up the "Telecommand Batt Low" problem again and will exit the Engineer Mode. How do I get out of this, as I say I have put new batteries in the remotes but this does not …

Having just been burgled I have purchased a KX15DATM pir from you to replace a failing unit from a different manufacturer. The existing unit is connected via 6 cables - 2x Tamper, 2x Relay and 2x 12v. Do you know what connectors the cables need to be screwed into on the KX15 please? I may also have to change some of the dip switches? The control panel is an Accenta 8.

My current alarm Guardall Rascal Super is broken so needs replacing(we are using 4 programmed zones and chime). I'd like to replace the control unit unit and bellbox but use existing wiring, sensors and internal speaker. I'm looking at the MDT Avanti 8 and AG6 bellbox (current bellbox looks tatty and has no strobe). 1. Is the chime quite loud? We would like to hear if someone enters the house from the other side of the building. 2. The Rascall Super system is 12v and I think the Avanti 8 is 13.8v, will our existing sensors work with the new control unit?

I am sorry to bother you again. Can you tell me please is it possible to get a wireless sender and receiver to fit inside the VERITAS R8 control panel as we have a garage that was alarmed that way as it is detached from the house and the old wireless sender is not compatible with your system. Also is there a code to open the panel to replace the battery as the installer took all the installation notes with him and he has gone to Australia for 3 months so i cannot contact him.

have just installed my new control panel everthing working fine, just won't let me change the four digit code, have gone through the instructions given in user manual but it still only lets me use the factory set code to set the alarm,could you please give me some advice to correct this problem.

I would like to know if you can help me specify a new system based on the Galaxy Dimension. I need it to be able to control 4 doors using mag locks / press to release. Video door entry integration and also intruder function. Proxy tag / swipe for enable/diable of the building alarm. I think I need a Galaxy Dimension GD-48 but need help with the other parts. You seem to be the best value and I need to make a purchase by next week at the latest.

I have your verutas 8 and i have just added another remote key pad, all works fine but i cant seem to get out of engineers mode, i go to program and put my new code in but when it comes to full alarm it will only respond to 4 3 2 1 any surgestions?