Intruder Alarms

Was wondering if you can supply a simple remote panel for the Optima Plus 2

Bought a Galaxy GD-48 with touchcenter all is All is ok except the front LED’s do not operate. System is ready but no green led , when you set the system, the system sets but the red LED is not on. System reports no faults or trouble and touchcenter LED test works fine all LED’s operate.

I'm looking to buy a Honeywell SS/01 SS/F Simple Set Reader for connection to a new Honeywell Accenta Mini G4 or Optima Compact G4. Is the relay return required from the simple set reader to the panel OR will it operate just using the normal 4 wire Positive, Negative, Sound and Comms?

i was thinking that i could use some wire and connect the auxiliary input of MC-302E PG2 with a outdoor PIR sensor but i don't know if this could be done.I was thinking of the OPTEX BX80 NR (maybe if it fits i install the MC302E PG2 inside the BX80NR)cause i can't imagine a way to have my balcony covered (12x2,4m) with the TOWER 20AM PG2. Do you think i could do such a thing? or what other option i have to cover this area with Visonic compatible product ?

I have installed this panel as a direct replacement to an older veritas excel panel as such 5 x pir, 2 x external sounders & 2 x smoke sensors are configured as previous eol set up ie 2 resistors in the sensors. I had a functional premier elite rkp to hand and have installed this with the new system. I cannot get the system to set up properly, it displays system alerts for the panel lid tamper etc even though the panel lid id closed securely as well as tamper faults for 2 of the 5 pirs, i cannot see any wiring faults and am now thinking this may be a panel fault, can you give me a little guidance please. Wondering whether to buy a coms cable and try to programme from…

bought a complete system buy you. Now I have a configuration issue. The alarm triggers directly when I enter, now entry delay is active. I have chosen 1. Exit/entry delay 1 for door contact and 3. home e/e for motion sensor in hallway. Is this correct? I want to be able to have Home zone active without triggering the alarm (except when door is opened). Should I choose antoher zone type for motion sensor in hallway?

I have just completed an instalation of a accenta G4 from yourselves,on powering up i can reset the alarm by entering factory user code but the display on the 2 LCD keypads is all black squares,please can you advise any help checked wiring but all seems correct with panel and both keypads.

I purchased a Honeywell Accenta Metal Gen4 Control Panel and Viper GLX Shock Sensors from you a couple of years ago (Order #16133). I am only getting around to installing the alarm system now and I have a query which I hope you can answer. Before I bought the house, part of the house had already been pre-wired with 4-core alarm cable. One of the pre-wired zones at the rear of the house is wired with 4-core cable and the sensor points are linked in series, i.e. the alarm circuit and tamper circuit are both linked in series. The cables to each sensor are connected under a tiled floor, so the junction box is impossible to access without breaking tiles. As the sensor loca…

I have a set of garages with two alarms installed that both join to a single masterblaster in the roof. I want a dialer that rings me or another member of the family if the alarm is triggered or the power is cut on the system. Sorry, I'm not very technical, but can the GSM dialer be connected in the roof space on the same wires as the masterblaster? Obviously the masterblaster will not work if the power goes down and so I wanted an autodialler as a back up. If so how much wiring would be needed and is it straight forward?

I am wanting to place an order but one of the items I want to purchase is a suitable motion detector for my timber workshop. Please can you advise me on what type of detector is best suited (most stable) to this environment where there will be temperature changes, possible insects and there is 3 windows. It is a good quality workshop like a log cabin, I have had a look at your sensors but I am unsure when it offers pir, microwave, dual tech etc ? Thanks

enter engineer program mode scroll thru to P enter3 inhibit zones press x 3 times leave engineers mode system unset enter user code press p LCD still only offers set program 1 no other option offered

Can you suggest a package to provide 3 x independently switchable on/off beams of 12m, 9m, 6m span with a control panel and sounder. The sounder to mute after a preset time. the system to be mains/ 12v powered. The detectors to be preferably powered from one end only of each beam. As cheap as possible, p.s. external use near the ocean.

I purchased an ade Optima Compact alarm system which I have fitted all seemed fine until I tried to alter the customer code from **** it would not accept the change but stopped the system from working. I have tried resetting the system back to factory settings as outlined in the manual but it does not work when the alarm is powered up it goes right into alarm but no LED lights show (not even the battery power)and the code **** does not rest/stop the alarm.

when setting the alarm i get the following error message + Line Failcom 1 what does this mean how do i get around this error message i am not connecting it to any phone line Also why does the Diagnostic LED flash- does this mean anything

I purchased a Meniver SD2 from you a while ago and have just got round to fitting it but it isn't working and I'd like some help to get it work. I have wired the autodialer into an alarm system and all appears to be good until the unit goes to dial out. I have run test facility and the unit opens the line and then dials, it's says on the screen wiring to dial. I can hear a dial tone before the dialling but the call does not connect. Then before you can hear any connection to the dialled number the unit starts to send out the recorded message after a few seconds. The line test on the unit shows that the line is ok and the fact that a dial tone can be heard before it dials…

My first question is can you confirm the total load current of the AG6 is 260mA max as I seen else where figures higher than this. The total load for the Logic six is only 1A. My second question is could the second AG6 be wired with only the strobe operating but keeping the anti tamper working? If so how would this be wired?

THE "HKC 2 WAY WIRELESS QUANTUM KIT" BUT THE CLIENT WANTS TO USE 2 ENTRY EXIT DOORS . SO I WANTED TO KNOW IF YOU CAN TWIN A PIR WITH A DOOR CONTACT AND PUT THEM BOTH ON THE ENTRY EXIT ZONE . SO THEY CAN SET THE ALARM SIMPLY BY PRESSING SET ON THE OPTIONAL KEY FOBS YOU SELL , INSTEAD OF OMITTING ZONES AND STUFF WHEN SETTING THE ALARM ON THE KEY PAD

I have a customer with a broken Veritas 8C controller. They have 2nd remote R8 keypad. If I install a new Veritas V8C controller is the old 2nd keypad compatible?

I have put in te GSM 350 PG2 module into the Powermaster 30 G2, but it don't seems to work. When I do a diognostic test it shows: "GSM not detected" What could the problem be??

Hi I ordered some Honeywell ECO1002 detectors with ECO1000BREL12L bases, I intend to fit install them on a Galaxy Flex 20 system, reading through documentation I believe I need non-latching bases is that correct and do the bases have the required resistors installed.

I am looking to get a security monitoring system were is no access for a landline (router) only to use GPS services. I was looking on connecting Visonic Powermax pro including Powerlink 2 unit with a sim card with data package. For a vision monitoring I want to connect a PTZ IP (axis???) outdoor dome camera which will be linked to the Powermax pro (how is it connected?) Could you please advice which camera will operate with this unit and how the system should work if the is only a mobile router (sim card with a data package) or is there some other solution how to connect this system and view it online?

We have a Visonic powermaster 10 with problems accessing the gsm network. I am not able to control it or obtain status reports via sms, and when I run the GSM/GPRS diagnostics it reports "Gsm net. fail". I am not aware of any issues with the SIM card or the subscription, but I thought I would try using another SIM. However, the installation manual clearly states no to insert or remove SIM card when the control panel is powered by AC or battery. Hence I need to remove the backup battery, but on page 59 in the user guide it is stated that I should contact my installer to perform the backup battery replacement. Since I installed the system myself, I do not have any insta…

Hi, How do you change user and engineer code to the Texecom premier 24 panels. The manual gives details to change from eighter 4,5 or 6 numbers. I have tried with no success to program with 4 numbers and won't except only if I use 6 digit. Please if any one can help I would be grateful as I don't want to use 6 digit. Thanks.

We recently bought some pendant transmitters from you for a Powermax+ Alarm system. I sucessfully installed 1 of them (more by accident I think) but am struggling to make the other work. I find the instructions very confusing! Please can you help...

Hello, I resently puschased a PowerMater 10 alarm system from you and am now starting to install the equipment. There is a problem with the display on the master unit, it seems like it doesnt remove some of the characters and some texts looks really weird. For example, int the start screen it says "15:16EADY : " where i guess it should say "15:16 : READY ". If I have a fault it switches between "NOT READY TRBL" and "15:16EADY : " There are also some really strange characters for the zone naming when I try to add equipment to the system. Everything else seems to be working though, I can add equipment and arm/disarm the system. I have tried doing a "Factor…