kyrusdemnati

check outputs? can anyone help me make sure i set it up right and what to check/fix i have paired my deltabell external sounder (see previous posts)problem i have now is whenever i enter my alarm code - the external sounder goes?when i do enter the codeit does bring up a message on the displayTesting....and then the standard now arming message...there is no alert about the external deltabell being triggered on the display panel and re entering the alarm code does not turn it off either. i have to access engineer menu and and exit and then it says 'saving nvm data' and it turns offproblem i have is i cannot set the alarm in either of my zones without the external sounder immediately going off?any advice on how i can fix this please?

i have paired my deltabell external sounder (see previous posts)problem i have now is whenever i enter my alarm code - the external sounder goes?when i do enter the codeit does bring up a message on the displayTesting....and then the standard now arming message...there is no alert about the external deltabell being triggered on the display panel and re entering the alarm code does not turn it off either. i have to access engineer menu and and exit and then it says 'saving nvm data' and it turns offproblem i have is i cannot set the alarm in either of my zones without the external sounder immediately going off?any advice on how i can fix this please?

hey guys i have done a reset of my alarm system (had front door changed which affected tamper on door and i made the mistake of resetting entire system) so i am at step one and i am struggling to configure how it was before. i will try my best to give as much detail as possible. This is the setting at the moment. And i have put in red, the bits i am struggling with and trying to configure ZONE A/B (when leaving the home) (KITCHEN MOTION SENSOR) - MODE 06 INTRUDER (LOUNGE MOTION SENSOR ) - MODE 06 INTRUDER (BEDROOM MOTION SENSOR) - MODE 06 INTRUDER (UPSTAIRS LANDING) - MODE 6 INTRUDER FRONT DOOR MC1MINI-WE - MODE FINAL EXIT/TIMED (SO THIS COUNTS DOWN FROM 25 SECONDS AND WHEN I CLOSE THE DOOR THE TONE STOPS) However when i open the door, the system doesn't give me a countdown to enter my code to switch off the alarm? (it used to do this before) ZONE B (NIGHT) - so i want downstairs active whilst we are sleeping upstairs (KITCHEN MOTION SENSOR) - MODE 06 INTRUDER LOUNGE MOTION SENSOR ) - MODE 06 INTRUDER FRONT DOOR - WHAT MODE SHOULD THIS BE ON? i think i have set this as timed Other Questions I do have a bell box, but i need to get a ladder and learn the device again. What mode should be set too? My backlight display on the device, times out so its blank after setting an alarm how do i make this visible at all times? I want to add 2 more MC1MINI-WE to my set up in the near future Upstairs Window Back Conservatory Door what mode do i need to put this on? Other information From my front door there is no motion sensor in the path of the Main Panel to trigger the alarm, as its near the door. I wont be using my back door as an exit/entry route to arm/disarm the alarm if you need any more information, please let me know, i would appreciate your assistance to get this working?

yes the control panel display, in the past it was always visible with the time and the name 'enforcer' - not sure if i turned it off by default somewhere

i can't find anywhere in the settings for the display to stay on? i went to screen display and everything is selected YES after a while it times out until i press the keypad... can anyone help thanks

Hi mate ok thanks so at the moment I have set up to motion sensors , kitchen and lounge I tested it and it works with the alarm triggering from the unit panel. (Still need to get a ladder and do bell box) but when I try and set the alarm again it brings up a kitchen error alert and it cannot set alarm . How do I reset this ... (my test was via the kitchen motion sensor ) What options do I need to select for each my sensors too, I’m not sure if I have done it right . What do I need to set as the type type Motion sensor 1 kitchen Intruder 06 motion sensor 2 lounge Intruder 06 (My other motions sensors will be ) upstairs landing sensor what input type ? bedroom sensor what input type ? Front Door sensor (this will be my entrance and exit to the house what input type do i need ? I also will be adding a 2nd door sensor to my patio door at the back house what input type do I need to set this too ? Thanks

it looks like my door sensor is damaged, i cant open the device - screw seems damaged so i can't repair and the backplate is broken slightly (i had my door changed) i have managed to pair my 4 pir motion sensors again all set for (zone A) kitchen, lounge, upstairs landing, bedroom - will add my front door (awaiting replacement sensor) I want to also set a night alarm (Zone b for downstairs which would be (kitchen) (lounge) (and front door (awaiting replacement sensor) is it a simple process to create a zone b? my questions are going forward. 1) i am going to order a new door sensor - is this quite straight forward to install? this would need to be configured as part of zone a and zone b 2) my bellbox is also not on the panel and needs repairing, do i need to get a ladder and resync or is there an easier way? does this have a similar pairing button that is found on the sensors which i press to sync, but i use learning devices bell option on the enforcer settngs right? 3) if i buy a Pyronix Enforcer Keyfob-WE - does this only work within the proximity of my home? I would just want to use this to set alarm/disarm, set zone a, set zone b, and panic alarm... thank you

Can anyone please advise? i have checked manual/interface its daunting i just need to know the basics please, everything is already in place - but .i changed my front door and the door sensor caused an issue/tamper and the alarm wouldnt set, and i made the mistake of resetting the device so i have lost all the devices from the memory thanks